At FXR Division, we're always doing things that are a little outside the box. That's why we offer a Split MX T Bar in:

• 12”

• 14”

• 16"

• 18"

• FXR Division Handle Bars are finished in a High Quality Gloss Black Powder Coat (CHROME IS NOT AVAILABLE AS IT HAS BECOME TOO EXPENSIVE AND DIFFICULT TO QUALITY CONTROL

  Our customers have been purchasing our FXR Division Bars and Crash bars in Black and having them stripped and plated locally to them)

In addition to giving you great looks, performance, and comfort, these bars are some of the easiest to internally wire! All of our bars work with Throttle By Wire OR Standard Throttle Cable Assembly...YES… Your OEM Throttle By Wire fits PERFECTLY!

At a width 29.5” End To End…Our FXR Division Split MX Bars are made with a 12 Degree Wrist Angle… as we have done the R&D and found this to be the most Natural Wrist Position and offers not only the MOST Comfortable Position while your hands are resting on Your Bars, but offers Performance as well… This is NOT Pullback as Pullback is in the Riser… Our “G Series” Bars offer a 1” Pullback in the Rise.

To ensure Maximum Strength, we manufacture all of our bars from 1.250 X .125 steel tubing and DOUBLE Stacked .750 DOM Supports for added Strength and Structural Integrity. All FXR Division bars go through our rigorous quality control process before they leave the shop.

IF YOU ARE PURCHASING OUR FXR DIVISION SPLIT MX BARS TO RUN IN CONJUNCTION WITH THE KRAUS MOTOR CO. RAPTOR PLATE…

12” FXR Division Split MX Bars DO NOT Require extending cables and/or lines on most models… Your Stock Cables should work just fine!!!

*** However, on M8 Softail models, wiring and brake line extension is REQUIRED and you can purchase our 12" to 16" T Bar Softail Low Rider, Lowrider S, and Lowrider ST Handlebar Wiring and Brake Line Install Kit, located on our site.***

14” FXR Division Split MX Bars… while we have had customers able to install WITHOUT extending Cables or Wires… it may not always be the case.

If have a Road Glide with a Hydraulic Clutch and/or ABS and you would like to extend your Clutch and ABS Brake Line… Parts RECOMMENDED and we SELL to to do so are on our “Clutch Cables, Brake Lines, and Fittings” page:

CAN BUS HANDLEBAR CONTROL WIRE EXTENSIONS

(1) GUERRILA CABLES Plug N Play CAN bus Xtra Length 34” (42” for 16 inch bars)

CLUTCH LINE

(1) Universal Clutch Line Adapter

(1) 70” Goodridge Clutch Line (71” for 16 inch Bars)

(1) Straight Banjo Fitting for Hydraulic Clutch Master Cylinder

TOP ABS BRAKE HOSE

(1) Goodridge ABS Adapter Block

(1) 60” Goodridge Brake Hose (63” for 16 inch Bars)

(1) Straight Banjo Fitting For Brake Master Cylinder

** If your OEM Perch Clamp has a locating pin… it will be necessary to remove it before installation**

*** Don't forget to get a set of NEW Handlebar Bushings to go with your bars!***

****We normally DO NOT stock bars over 16”… they are Made To Order and may take a little bit longer to manufacture and ship… Orders for Bars over 16” WILL BE subject to a 20% Cancellation Fee if order is cancelled after 7 Days from the Date the Order was placed***

We do our best to have ALL of Our FXR Division bars IN STOCK. However, if they are not immediately available… then they are currently IN PRODUCTION.

If do not receive a Shipping Notification, with your tracking number within 1-3 business days… Then please allow 2-4 weeks for orders to ship.

NOTE: INTERNATIONAL PRICING MAY VARY